Laser Weapons

Lasers at the Starfire Optical Range.

Lasers are common in science fiction as futuristic weapons. Lasers project light at damaging intensities onto a target. To be effective, this light must be focused through optics (laser beams do not travel as perfect columns! Focusing makes the beam converge to a tight spot on the target). The ability to focus is limited by diffraction and, in an atmosphere, thermal blooming; and energy can be lost from the beam due to atmospheric absorption, scattering, and other phenomena. The color (wavelength, frequency, or per-photon energy) of the light you choose can be very important for your ability to get the light to the target.

Lasers can be expected to be exceptionally accurate. Depending on the power, energy, and intensity you can deliver to the target, they could be limited to relatively shallow surface burns or could drill deeply enough to reach vital equipment or organs deep inside the target. You can defend against lasers with armor or smoke, but mirroring will not work against higher intensity lasers.

Certain colors of lasers can cause unintended blindness to bystanders or friendlies, including all visible colors of light. Use with caution.

Introduction

Lasers are remarkable tools, with a wide range of applications across all realms of technology - communications, medicine, remote sensing, computing, data storage - but of course you don’t care about any of that. No, what draws us to places like this is using lasers to blow stuff up! So what is a laser, anyway? What makes it good at blowing stuff up, and why can’t it blow stuff up even better?

When we think about some new technology, we often default to thinking about it the same way as some analogous technology we are already familiar with. Early writers imagined airplanes as giant cruising air battleships rather than jet fighters. Early robots were very often metal humans that could talk and sense and interact with their environment rather than mechanical arms carrying out rote motions in factories or disk-shaped vacuum cleaners. In the same way, we often default to thinking about laser weapons as just like bullet-shooting guns. But they are not. Laser weapons, even laser guns, will be shaped by their own physics and design constraints into machines that optimize their potential and very often this leads to appearance and behavior that will be very different from the bullet guns that we expect.

If you look at the usual definitions of a laser, they will say that a laser is a device that uses stimulated emission to produce monochromatic, unidirectional, coherent light. All of this is mostly correct, but there are exceptions to each of these cases. Real life gets complicated!

• Stimulated emission is a process where an atom, molecule, or other quantum system in an excited (energized) state can be made to transition to a lower energy state by being hit by a quantum unit (or particle) of light (a photon), and in the process produce a second photon that is identical in every way to the first. Stimulated emission is a useful method to make directed beams of light, but there are machines called lasers that produce laser-like light without stimulated emission.
• Monochromatic means the light the laser produces is only one color (or wavelength, frequency, or photon energy … any one of these terms suffices to specify the color). In fact, monochromatic means that the laser is exactly one color - but this is unphysical. Every real phenomena has some finite distribution of colors, even if this distribution is so narrow that it can be hard to detect and can be neglected for many purposes. Most lasers are very close to only one color. But a number of lasers, especially those made for extremely high powered pulses, produce beams with a wide spectral range of colors.
• Unidirectional means all the light is going in one direction. As we will see later, this is ultimately not possible. The wave nature of light makes light that seems to originally be going in the same direction eventually diverge. In fact, it is often helpful to have the light coming out of a laser be slightly diverging or converging, and adjust that later with lenses or mirrors.
• Coherent (or, for our purposes, transversely coherent - there’s also longitudinal coherence but we don’t need to worry about that here) means that if you look across the beam at any given distance along the beam, all the light will be pointing or wiggling the same way. It is this property that allows lasers to be focused and directed so well. Loss of coherence means your beam can’t focus as well as it potentially could. Even incoherent light can be focused to some extent by forming an image - witness using a magnifying lens to focus sunlight - but coherent light can be focused much better.

Fundamentally, a laser is a tool that amplifies light. But even if we could, we wouldn’t want to amplify just any old light. No, we want to amplify light that has only those properties we want. For laser combat, that usually means light that will be focused on the target after going through the appropriate optics.

Technically, what happens is that to make it efficient to amplify light, we put the light we are trying to amplify into a cavity, a structure that allows light of a certain kind to resonate (or bounce back and forth a very large number of times with little loss). The material, substance, or device that amplifies the light is called the gain medium. This gain medium is placed so that the resonating cavity light goes through it, getting amplified with each pass.

The ways that the light can bounce around inside of a cavity are called its modes. A given mode will have only one color, and will have a specific relative intensity and direction profile that depends on the geometry of the cavity. The light in a given mode might be converging (focused) or diverging (defocused), but that can be altered later with optics. Any single mode will be fully coherent. The gain medium will usually only allow certain colors to be amplified, and thus only certain cavity modes can be excited. What we want to do is arrange the cavity so that only the modes that are most useful to us are amplified. When we do this, we can make beams with a minimum divergence that we can focus to destructive power on our enemies.

The Nature of Light

Lasers emit light. So to understand lasers we need to understand light. Lasers and the electromagnetic spectrum goes over some fundamental properties of light, and how the different colors of light impact what your laser can do.

Focus

Boeing YAL-1 Airborne laser beam pointer turret.

Tactical High Energy Laser (THEL) beam pointer.

The laser beam pointer of the AN/SEQ-3 LaWS (Laser Weapons System) aboard the USS Ponce.

So, we have a beam of really bright light that’s mostly one color and going mostly in one direction. That’s great. Now what? If you are fighting someone, you probably want to shine that light on them. And you probably want the light to be as intense as possible when it gets to them. However, if the intensity of the laser is too high while it is in your laser generating machinery, it will melt all that expensive machinery that is making the laser. You need the laser to be spread out enough in your laser gun that your laser gun can survive, but intense enough at your target that you can do bad things to it.

The trick is to use a lens or mirror to focus the laser to a tight spot on your target. This lets you use a large, spread out beam in your laser gun, but still blast your target with concentrated energy!

To do this, you need to be able to focus the laser at different distances. Also, you need to know the distance at which the beam needs to be focused. If you get either of these wrong, your target will just get heated up a bit, or get a painful but mostly harmless surface burn. The first issue can be solved by using motors and moveable or deformable lenses or mirrors. This is similar to the auto-focus technology of modern cameras. The second issue also uses the same technology that cameras use, either by bouncing a ranging laser pulse off whatever the laser is aimed at and seeing how long it takes to return, or by adjusting the focus until whatever is aimed at displays crisp lines. A consequence of all this is that laser weapons will see their beams directed to some large focal assembly that looks like a large camera lens or telescope mount, rather than just taking the beam that comes directly out of the laser generator.

But you want a big focusing aperture for more than just preventing damage to your beam optics. A wide aperture also lets you better overcome diffraction to focus better at longer ranges. In addition, in the air your ability to focus will be limited by thermal blooming, twinkle, and jitter. If your beam is too high powered and you focus too much, you will run into problems with thermal blooming, two-photon absorption, stimulated scattering, and cascade breakdown.

Diffraction

Diffraction gives the ultimate limit to how well you can focus your laser light. This page covers the effect in more detail, but the end result is that the larger your focal aperture, the shorter the wavelength of the light you are using, or the shorter the distance to your target the tighter your focus will be.

Beam-Atmosphere Interactions

Getting light through air can be tricky. Sure, we can see through air just fine, so maybe you’d think it wouldn’t be too much of an issue. And sometimes it isn’t! But when the intensity of the light gets really high all sorts of crazy non-linear things can happen. We’ll try to go through the more important of these things so you can get some idea of what the limitations are for your laser and how you might get around them.

If your only concern is blowing up enemy spacecraft with your own spacecraft, you don’t need to worry about atmosphere because there isn’t any. Have fun floating around up there in orbit, though, wistfully gazing down on all those nice juicy targets that you can’t blast with your vacuum-only rated lasers.

• Attenuation will remove energy from your laser beam, giving less juice to blow up your target. There are two main forms of attenuation:
  • Absorption.
  • Scatter.
• Twinkle can make your beam wander around randomly and lose focus if you don't correct for it.
• Thermal blooming will make your beam lose focus. It is a non-linear phenomenon so you need to be careful that the steps you take to correct it don't just end up making it worse.
• Two-photon absorption can absorb high power pulses of ultraviolet light when they are tightly focused.
• Stimulated scattering turns your laser into a laser ith the result that energy is removed from your beam. It is mostly important for high power pulses.
• Cascade breakdown can occur when a beam of longer wavelengths is focused too tightly. It turns the air into a plasma, which absorbs the beam and prevents it from getting to your target.
• Atmospheric hole burning might allow the really high frequency beams that are rapidly absorbed by air a way to get through the air anyway.
• Filamentation is a strange phenomenon where the light in your beam self-focuses. Laser filaments have unexpected behavior – they might cause problems but they might end up being useful.

Accuracy

Before your beam can do anything, you need to shine it on your target. Fortunately for you (and unfortunately for your target) lasers can be exceptionally accurate.

Deflection

Imagine shooting out a ray of light. It goes through an optical obstacle course, consisting of any variety of lenses, prisms, and mirrors until it finally lands somewhere on a screen and makes a bright spot. So here’s a neat trick - if you take the light at the spot and reverse its direction (or perhaps more practically, put a light source at the spot that shoots out a ray backwards along the direction that the original ray came in at), the resulting ray moves back exactly along the path it originally took, retracing the same route through the mirrors and prisms and lenses, so that it ends up at the original source.

Now let’s see what that means for lasers. Suppose you have a laser gun. You see your target in your scope and you line up your scope reticle with the image of the target, then slowly squeeze your trigger. Zap! You send a beam of collimated photonic death at your enemy. But wait! It is a hot day, full of mirages, and the heat distortion is bending the light from your target so that it takes a round-about path to get to you. Your laser was never actually pointing at your target. Surely you must miss, right? Well, no. Because the laser beam takes the same path back to the target as the light from the target took to get to you. As long as you aim at the target’s image, no matter how it was displaced by optical trickery, the beam will arrive at the target.

In this way a laser can be much more accurate at long range than bullet guns, which have to contend with drop due to gravity and deflection by the wind.

Leading the target

Laser beams also travel much faster than bullets. Any waterfowl hunter knows they need to lead their target by a bit if they want duck dinner, because it takes the shot a slight amount of time to get there. Laser beams travel so fast that over planetary scales you don’t need to worry about leading your target.

Over vast distances in space, though, even the incredible speed of light gives a slight lag between when the information you are using for targeting is given off by your target, and when the beam reaches your target. If your target is moving on a known trajectory, you can correct for this and most spacecraft gunnery control systems should have this functionality. But this lag does give the target a small amount of time to dodge your beam.

This light lag might never be a problem, even in space, for some kinds of lasers. A visible or near visible light wavelength would need to be focused through an impractically large mirror to cause damage out to even a light second with any reasonably achievable beam power, due to the focusing limits of diffraction. So for lasers like this, lag and dodging will not be a problem. But to get very long range lasers by going farther and farther into the ultraviolet or x-rays, or by making enormous focusing mirrors, may give you beams that can reach many light seconds or even light minutes. At these ranges dodging becomes an issue. Very long range lasers might end up being tools that force an enemy to expend propellant to avoid being hit, eventually resulting in insufficient propellant left to complete their mission.

Parallax

The scope on top of a rifle is set maybe 6 cm above the barrel. So if the scope is perfectly aligned with the barrel (it isn’t) and the bullet goes exactly straight (it doesn’t) , when you shoot a rifle you will hit about 6 cm below where you shot at. This is called parallax. Usually, this being within 6 cm is adequate - it’s still close enough for a hunter to put a bullet through a deer’s vitals, or a sniper to drop a terrorist with a shot to the center torso. (As an aside, scopes are usually set up to point somewhat down compared to the barrel, so that the initial rise of the bullet is pulled back down by gravity, and the bullet first rises a bit above the line of aim before coming back down - thus nicely countering one effect by the other and extending the distance over which you don’t have to adjust for bullet drop considerably.)

But what if we could do better? A laser uses optics to focus the beam. The shooter uses optics to aim the beam. So let’s use the same optics for both purposes. This idea is common in cameras, where it is called a single lens reflex camera. A flippable mirror directs light from the lens to an eyepiece, showing exactly what the camera will record when you click the shutter and flip the mirror around so the light goes to the sensor (or film) instead. You can do the same thing with your laser gun, except that now instead of letting the light in to a sensor you let the light out from the laser beam generator. Either way, the laser beam goes directly to where the reticle was pointing, without any parallax at all.

Jitter

Sometimes it's not so much about how much the beam itself moves around, but how steady you can hold the beam. This page covers much of the issues with jitter on fixed mounts. Hand-held laser weapons will mostly be limited by the jitter imposed by the person aiming the gun – their breathing, pulse, tiny muscle tremors – all these can throw off a gunner's aim. Fortunately, modern camera makers have come up with ways to correct for that. Electronic auto-stabilization that works on consumer camera optics will also work on laser optics, making it easier to hold your aim rock-steady.

Recoil

A gun that shoots bullets will kick back as the bullet is launched. This might be from the pressure of the gas inside the barrel pushing back on the gun. For a science-fictional gauss gun, it might be from the interaction of the induced currents in the bullet with the magnetic field and the currents in the gun’s barrel. But no matter how you do it, Newton’s laws of motion and the conservation of momentum mean that when you shoot the bullet forward, something else has to go backward and almost always that thing that goes backward is the gun.

Recoil has a number of drawbacks. If you don’t have experience shooting and you are holding the gun wrong, it can knock you off balance. If you are shooting really big bullets going really fast, the gun recoiling can hurt or even leave bruises, especially if you are a small framed person. Many shooters start to subconsciously anticipate the kick, and flinch as they pull the trigger which will throw off aim. Most seriously, perhaps, is that when you are shooting rapid fire the recoil makes it hard to control the gun. On fully automatic fire, after the first two or three bullets the rapid recoil usually torques the barrel of the gun up into the air so all you are shooting at is the sky. And for really big guns, like cannons, you need to engineer in shock absorbers so the recoil doesn’t damage the cannon’s mount or throw off the aim of subsequent shots.

Lasers don’t have this problem. Or rather, if they do have this problem you are dealing with such massive overkill that your battlefield will look like nothing we have ever experienced. For any practical laser power, the recoil will be so minuscule that you can’t notice it. Lasers do produce a tiny amount of recoil. The force they give is the power divided by the speed of light; the total momentum given to the gun is the energy divided by the speed of light. Because light is so incredibly fast unless the power and energy is extraordinarily high the recoil will never be felt. If your laser kicks with the recoil typical of a normal gun, you are throwing energies typical of the detonation of tons of TNT downrange at your enemies with each shot.

Effect on target

So now you are shining an intense beam of light on your target. What does it do? Does it just smoulder? Does it burst into flames? Is it drilled through in a shower of sparks? Does it explode messily? This page will help you find out.

Defenses

So we’ve been having fun pretending to blow up bad guys with lasers. But what happens when it’s the bad guy that has the laser? How are we going to protect ourselves from becoming the extra crispy variety of barbeque?

Smoke

The first step in not getting shot is not being seen. While stealth methods have long been known and used to prevent the enemy from shooting at you, for lasers not being seen has an additional meaning. Lasers operate by emitting light. If light can’t get between you and your attacker, his beam can’t reach you. It doesn’t matter if the evil emperor's goons have a precise lock on you with their radar. If you are behind a kilometer thick fog bank, their laser guns are not going to reach you.

Now clearly, mere darkness is not going to stop a laser. Even if your foe can’t see you because the lights are out, his beam can still get to you. But if you can put something in the way that will absorb or scatter the light out of the beam, then his beam can’t reach you and you will be safe. This might involve deploying a smoke screen. Or flying above the clouds - or below the clouds if the enemy is in orbit and you are not.

A rough rule of thumb for visible and near-visible colors is that if they can see you through clouds or smoke, they can shoot you with the laser. This is not a strict rule. Human eyes are good at picking out low-contrast or faint patterns, so the smoke might let someone see faintly through it but still attenuate laser beams to near uselessness. But there are factors that also swing the other way, too. A lot of the reason that we have trouble seeing in fog is not just because light is being scattered out of the path between us and the thing we are looking at, making it dimmer; but also because other light is getting scattered into the light path from the sides, which reduces the signal to noise (or contrast, if you prefer). A laser beam will be affected by the first of these, but won’t care one whit about the second (although the second effect will make the whole fog bank light up like a colored flash bomb when the beam turns on). Taken together, this usually means that if the bad guy can’t see you (which, due to the reversibility of light paths means you can’t see the bad guy) he can’t shoot you. If he can barely see you, he can shoot you but with reduced effectiveness. And if he can see you clearly you’ve got no protection from his laser beam.

Very powerful beams might be able to burn through smoke or fog. This is more difficult when the beam is wide (near the shooter) than when it is focused and narrow (near the target) because it will be of lower intensity and will also have to burn more junk out of the way. The upshot is that if you can burn aerosols out of the air, it is harder to shoot out of your own smokescreen than it is to shoot into it.

On the other hand, smoke that absorbs light will make thermal blooming much worse. You might be able to get your beam to your target, but the beam may be so smeared out by thermal distortion that it doesn’t do much.

Of course, you don’t need a cloud of aerosols to block a light beam. A solid barrier can do so as well. A sheet of paper could, in principle, stop the beam. If the beam is still spread out and not focused, it might not have enough intensity to burn through. Even if it can burn through, it might spend enough energy doing so that the effect of the beam is reduced. If the beam is focused on the paper sheet, it will blast through no problem. But then the beam is focused on the paper - not you. When a beam focuses to a point, it then starts to spread out again once it gets past that point. In photography, this is called depth of field. When you focus on something, both the stuff in front of and behind the thing you are focusing on can be blurry. The same effect in lasers is depth of focus, where if a beam focuses on something and shoots through it, it will spread out and become less intense once it passes through its focus point. So if you are hiding in bushes, the laser that your enemy shoots at you might put holes in a few leaves and sticks but if you are far enough into the bushes the beam might not have much of an effect on you by the time it reaches you.

One complication of all this “not being seen” stuff is that it is assuming visible or near-visible light beams. A glass window might let you see through it and even shoot a visible light beam through it, but glass is good at blocking ultraviolet light. If you tried to shoot through the glass with an ultraviolet-B beam, the glass would act like an opaque barrier. Likewise, fog will affect infrared light differently from visible or ultraviolet light. To make things even more complicated, “infrared” is a very broad spectral range, and light at one color of infrared will go through fog quite differently than light at another color of infrared. So when you start getting to off-visible colors, a more useful comparison might be “if your enemy can see you with a sensor that detects the same color of light as the beam he is using, he can shoot you.”

And mirrors

So we can defend against laser beams by absorbing or scattering the beam out of the way. What about reflecting it? It seems like everybody’s favorite laser defense is covering themselves with mirrors. But does it work?

The answer is “it depends, but mostly no.” The problem is that mirrors are not perfect. And even if you could somehow make a perfect mirror in the clean room of your multi-million dollar laboratory facility, it will not long remain perfect once it is out in the environment collecting dust and corrosion and micro-cracks and who knows what. The mirrors used for your beam guides and beam pointer telescopes can be sealed away. Mirrors used for armor - not so much.

That can be okay for heat ray type lasers. If you have an outer surface that reflects away 80% of the incident light, that can be enough to keep you from getting a hole melted through your innards, or catching on fire, or something equally bad.

But once the intensity at the point of focus of the laser starts getting more intense than heat ray scales, bad things start happening to the mirror. The small amount of light the mirror absorbs starts to damage the mirror. And if the mirror gets damaged, it doesn’t work as well so it absorbs more light. So it gets even more degraded. And then you don’t really have a mirror any more. This will happen very quickly, once the mirror starts to degrade it is all over. Some very intense pulses can just bypass the reflectivity of a mirror altogether, with electric field strengths high enough to simply rip electrons right off the atoms so that mere linear optical properties like reflectivity mean nothing. The mirrors used to direct and focus the beam work with the beam dispersed over a larger area and are thus protected. If the beam is focused onto a tiny spot, it could damage even the same mirrors used to direct it.

But there is one way that mirrors could potentially help against lasers. Remember that the laser needs to be focused on its target. If the laser beam pointer can’t get the right range to the thing it's pointing at, the laser will focus someplace else. A mirrored surface can potentially confuse most methods of range finding. Send out a ranging laser pulse and see how long it takes to come back? Oops, the beam pointer measures the range to the image reflected in the mirror, not the mirror. Use passive methods of adjusting focus until the lines are sharp? Same story. So if you wear a really shiny suit, your enemy’s lasers just might focus on whatever they see reflected in your mirrored suit instead of you. And then the laser is not tightly focused when it hits you and your mirror works just fine to bounce the beam away to whatever it thinks it should be focusing on.

Armor

The time-honored way of protecting yourself from something bad is to put a bunch of stuff between you and it. Usually something that is strong and tough. With the hopes that the bad thing will not be able to get through the strong and tough stuff, give up, and go someplace else.

This works for lasers, too. Armoring is a perfectly reasonable way to keep a laser from blasting your innards into outards.

Against a laser of heat ray intensity, mirroring has already been mentioned. In addition, it will help to use materials with a high melting temperature, high thermal conductivity (to wick heat away from the laser-heated spot), high specific heat capacity (so it can absorb a lot of heat without raising its temperature too much), and preferably something that won’t thermally decompose or catch fire. Active cooling can also help - send a flow of water or other coolant through capillary channels to absorb the heat and transport it somewhere else.

When the laser gets intense enough to start melt ejection, you probably don’t have much time to engage in active cooling. But a high specific heat of fusion (the amount of energy it takes to turn something into a vapor) will help.

For lasers that are so intense that they are blasting out craters or channels in things through the sheer force of their vapor pressure, thermal properties no longer really matter. All the damage is mechanical, so you want the same things that will protect you against bullets and explosive blasts. A high strength-to-weight ratio is good for making it difficult for the pulses to blast very far into the armor. And a low brittleness will help you take multiple hits without your armor shattering.

As a laser gets closer to its target, its spot size gets more tightly focused. And a very small spot size makes the laser more effective at penetrating armor. More so than bullets, a laser’s ability to penetrate armor will fall off with range, and will also increase faster as range decreases. A laser gun shooting a train of blast-pulses with the same overall energy of a bullet will punch a significantly deeper hole through armor at close enough range where the focus can be kept tight.

The main limitation on how much you can increase your armor penetration just by getting closer so you have a smaller spot size and more concentrated beam is that lasers have trouble drilling out holes with too high of an aspect ratio. Plausibly, a laser could drill a 1:20 or even 1:30 aspect ratio hole in a target’s armor, but is likely to stall out around that depth. If you get even closer, you won’t drill deeper. So get to within the range where your laser is giving you its maximum achievable aspect ratio hole, and shoot from there.

Deflector shield force screens

Science fiction likes to imagine fantastical technology that projects invisible barriers that stop incoming attacks. Note the "invisible" part. These technological force screens are almost invariably portrayed as letting light go right through them. Logically, this means they won't do much to a laser beam; at least not a visible light laser beam. If the force screen is a completely reflective perfect mirrored surface or totally black sphere of inky onyx midnight or something, protecting from laser beams becomes a lot easier to justify. But then of course the people inside can't see out. So choose your poison.

Safety

Eye safety

The cornea, lens, and vitreous humor of the eye are transparent to wavelengths between roughly 0.350 μm and 1.4 μm (the entire visible range, as well as near infrared and part of the ultraviolet-A band). Light that scatters off of your target can be focused by your very own eyes into an intense spot on your retina that can cause burns and permanent injury. Even the light that remains after multiple reflections can be hazardous. High power lasers in this wavelength range can cause instant total and permanent blindness. Anyone working with laser weapons in this range will need to take precautions to protect their eyesight. Not every eye injury will be permanent. Bright lasers can also dazzle, leave you seeing spots, or temporarily blind you. And some injuries may only cause permanent partial loss of vision. But this is a major concern anywhere that lasers are used.

Note that part of the wavelength range of eye-hazardous light is invisible. You might never see the beam that blinds you. But every visible light laser weapon represents a threat to your eyesight.

The incandescent plasma produced by an incident laser beam can also be bright enough to cause eye damage. This is less hazardous than the directly scattered light from the beam, however - similar to the danger involved with directly viewing an electric arc.

Eye damage from indirect exposure to the beam can be avoided by wearing protective glasses that filter out the wavelength of the laser being used. If you want to have a laser gun that can be used without worrying about blinding people without eye protection, you can use short-wave infrared or longer wavelengths (wavelength > 1.4 μm) or the higher registers of the UV-A band or shorter wavelengths (wavelength < 0.35 μm).

Ionizing radiation

Some lasers emit beams of ionizing radiation. Ionizing radiation is radiation whose energy-per-photon is high enough to knock electrons off of atoms, creating ions. Free ions in tissue can attack cells, causing cell death, mutations, or cancer. This is the same stuff people worry about when exposed to radioactive elements or nuclear technology. The main wavelengths to worry about are hard x-rays and gamma rays. Light with these wavelengths can penetrate deeply through matter and deposit their energy inside the body. At high enough doses this can lead to increased cancer risk, sickness, or death.

Technically, extreme ultraviolet and soft x-rays are also ionizing radiation. But since they can’t get through air, clothes, or environment suits they are not much to worry about. Even if you do reach you, they will primarily cause radiation burns similar to sunburn on your skin, which is definitely unpleasant and will increase your risk of skin cancer, but not nearly as bad as having all your bone marrow killed so you die slowly of anemia and infection like the deeply penetrating forms of radiation.

But what if you don’t have a laser that emits ionizing radiation? Do you have to miss all the fun? Not necessarily. Absurdly high intensities of non-ionizing radiation can do crazy physics shenanigans that result in the production of some ionizing radiation. These kinds of laser intensities will probably be confined to laboratories, because you don’t actually need situations that extreme to blow a hole in somebody and that kind of intensity in air can actually impede the propagation of your beam in many cases. But who knows? Maybe future research will show that the best way to blast bug eyed aliens is to make uber-powered beams that kinda sorta make some ionizing radiation as a minor side effect. Nothing to worry about, citizen. Move along. Our experts have it all under control.

Gun safety

There are certain basic precautions that should be used with any ranged weapon, including laser weapons.

• Treat every laser weapon as if it were charged and ready to fire. Always keep the aperture pointed in a safe direction.
• Keep your finger off the trigger until you are ready to fire. Use your safety, but remember that safeties sometimes fail.
• Be sure of your target and what lies behind it before firing.
• Never use a laser weapon unless you are familiar with how it works.
• Be sure the aperture is clear of obstructions.
• Never point a laser weapon at anything you do not want to shoot.
• Remove the power source of a laser weapon when not in use. Store power supplies and laser weapons separately.
• Never use alcohol or drugs before or during shooting.

If you are designing a hand-held laser weapon for your science fiction setting, there are a few common-sense safety designs to include in your weapon. Trigger guards, for example. You don't want some stray branch or obstruction to catch on the trigger and shoot a hole in your foot. Safety switches are also a Really Good Idea, to help prevent negligent discharges.

Laser Technologies

People have invented many different kinds of lasers. This page summarizes some of the more important ones from a weapons perspective.

Credit

Author: Luke Campbell